Something stopped working, or something is behaving the way it should not. A breaker that trips and will not reset. An outlet that has gone dead for no obvious reason. Lights that flicker when the air conditioning kicks on. A panel that hums or runs warm. You do not need to know what is causing it before you call. Describing what you are seeing is enough, and we can scope the job from there.
We handle the full range of residential and commercial electrical work across Wildomar and the surrounding Riverside County area. Whether you own a home here, manage a rental property, or run a business, we are available every day from 6 AM to 9 PM.
Call (949) 514-6953 and we will give you a price before anything is scheduled.
That is how we work, and we work the same way every time.
A vacant property is the easiest window for electrical work that would otherwise mean disrupting somebody's day. No tenant to coordinate around, no business hours to work inside, no occupied rooms to close off while the wiring gets traced. Access is arranged on the call when the job is scoped, and we confirm what needs to be open before we arrive.
Landlords and property managers in Wildomar often use a turnover to address work that has been deferred. An outdated panel, an outlet that has never been right, a circuit that was added without being documented properly. Getting it done between tenants means the next lease starts with the electrical system in the condition it should be in, and the work does not have to be worked around a schedule that is not yours to set.
If the property is occupied and the work cannot wait, we handle that too. Scheduling is covered in its own section below.
An electrical safety inspection is the right starting point when a property has not been looked at in a while, when it is changing hands, or when the wiring is old enough that nobody is certain what is there. We go through the panel, the outlets, the grounding, and the visible wiring, and we document what needs attention and what does not. A report after an inspection gives a landlord or a buyer a clear picture rather than a guess.
Fault finding is a different kind of visit. An intermittent trip, a circuit that loses power under load, a breaker that resets fine but trips again within hours - these take time to trace because the fault does not always show itself immediately. We work through the circuit systematically, check for arc-fault conditions, and find the point where the problem actually lives rather than replacing parts until something sticks.
A Level 2 EV charger needs a dedicated 240-volt circuit, and that circuit needs a panel with room to carry it. Before any charger goes in, we check what the panel is already carrying and confirm the service can take the added load. If the panel is already near capacity, a service upgrade is part of the conversation before anything else is scheduled.
EV adoption across this region is high and still growing. Homes that were built before EV charging was a common consideration often need a circuit added and sometimes a panel upgrade alongside it. We handle both sides of that job.
Outdoor lighting comes up for a few different reasons: a security concern, a property that needs better coverage after dark, or a landscape installation that requires a circuit run from the panel to the yard. Weatherproof outdoor outlets and enclosures go in alongside lighting work or as standalone installs when a patio or driveway needs a power point that can handle the weather.
Motion sensor lights and security lighting are wired correctly when the circuit is run right the first time, with weatherproof boxes and the correct outdoor-rated wiring. A plug-in strip on an extension cord is not the same thing, and it does not hold up.
A new appliance, a hot tub, or a workshop tool that draws a serious load needs its own circuit. Sharing a circuit with other loads leads to nuisance tripping and, over time, wears on both the breaker and the equipment. We size the circuit for what it feeds, run the wiring correctly, and install the right breaker at the panel. For 240-volt loads, that means the right gauge wire and the right double-pole breaker, not a workaround.
We know schedules shift, so we keep booking flexible, and that applies whether the property is vacant, tenant-occupied, or a business that cannot close for the day. When you call, we go through the job, confirm what access is needed, and find a time that works. There are no forms to fill out and no waiting for a callback before you know what the work costs.
For a problem that will not keep, we take short-notice work.
If something has gone wrong and waiting is not an option, call (949) 514-6953 and describe what is happening.
We will tell you what the schedule allows and get it on the calendar.
For occupied properties and businesses that need to stay open, we plan the visit around what can realistically be isolated. Most outlet, switch, and fixture work affects only the one circuit being worked on. Panel work is different, and that is covered below. The process is written out on our services page.
For most repairs and installations, only the circuit being worked on needs to be de-energized. The rest of the property stays live. That means a tenant working from home keeps their connection, and a business trading through the visit keeps its registers and equipment running. We confirm which circuits will be affected on the call.
Panel work is different. Replacing a breaker panel or upgrading the service entrance means the main breaker comes off, and the whole property loses power for the duration of that work. How long that takes depends on the scope, and we give a realistic picture of the timeline before the visit is scheduled. For a home where somebody works remotely, that conversation happens before we book, not when we arrive.
Arc-fault and ground-fault breaker upgrades can usually be done circuit by circuit, which keeps the outage scope narrow. A full service upgrade is a bigger job and gets planned accordingly.
When a property is asked to run something it was never wired for, the panel is usually where the problem shows up first. A hot tub, a Level 2 EV charger, a workshop with a 240-volt compressor, or a new HVAC unit that draws more than the old one, each of those adds load that the existing service may or may not be able to carry.
We start with a load calculation. That tells us what the panel is already carrying, what headroom is left, and whether the new circuit fits inside the existing service or whether a service upgrade is part of the job. If the panel has breaker space and the service is sized correctly, the new circuit goes in without anything else changing. If it does not, we explain what the options are before any work starts.
Subpanel installation is another path when the main panel is full but the service entrance has capacity to spare. A subpanel in a garage or workshop adds circuit space without replacing the main panel. We assess what is there and explain which approach fits the situation.
We service this area, and its neighborhoods each have their own wiring. Older homes on original panels, newer builds with modern 200-amp services, and properties that have had circuits added over the years without always being documented, all of those call for a different starting point.
You get the rate on the phone before anything is scheduled. The scope of the job, what the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change are the things that move the number. We explain what goes into it so you know what you are paying for.
For a straightforward outlet replacement or a ceiling fan install, the scope is usually clear on the call. For a fault-finding visit where the symptom is intermittent, or for a panel upgrade where the load calculation is part of the work, the price is confirmed once the job is fully scoped, before any work begins.
There are no forms to fill out and no waiting for an email.
Call (949) 514-6953, describe what is happening, and we give you a price on that call. Pricing is explained up front and covers what the visit involves.
We cover Wildomar and the surrounding Riverside County area every day from 6 AM to 9 PM. Nearby communities we work in regularly include Canyon Lake, Murrieta, Lake Elsinore, Menifee, and Lakeland Village. If you are in one of these areas, the process is the same: call, get the scope and the price on the phone, and schedule when it works.
Safe wiring. Solid workmanship. Straight answers.
It depends on what the panel is already carrying and how much headroom the service has. A load calculation tells us whether the new circuit fits inside the existing service or whether a panel upgrade or subpanel is part of the job. We work that out on the visit and give you the options before anything is scheduled.
Often yes. A full rewire is warranted when the existing wiring is unsafe throughout or cannot be adapted for modern use. In many older properties, targeted repairs, circuit additions, and panel upgrades accomplish what the homeowner needs without touching every wire in the building. We assess what is there and give you a realistic picture of the options.
Yes, and combining them is usually the more practical approach. When you call, describe everything you want addressed and we scope the full list on the phone so the visit is planned to cover all of it. One call and we schedule accordingly.
The electrical supply to a heating or cooling unit, meaning the dedicated circuit, the disconnect, and any panel capacity work needed to carry the load, is our work. Installing, repairing, or servicing the heating or cooling equipment itself is a separate trade. We handle the power side and confirm the circuit is correctly sized for the unit being connected.
Outlets near pools and ponds have strict placement and protection requirements. GFCI protection is required, the outlet must be at the correct distance from the water's edge, and the cover must be rated for wet locations. We confirm the requirements for the specific installation before the work is quoted.
Homes built before the 1970s often carry wiring that was never designed for the loads a modern household puts on it, including knob-and-tube wiring and aluminum branch circuits that require specific handling rather than a straightforward replacement. Panels from the same era are commonly undersized for the loads a modern household draws. We assess what is there on the visit and explain what the situation calls for before any work begins.
We work from what we find. Tracing circuits, mapping the panel, and identifying what is behind the walls is part of how we approach properties with no documentation. It takes longer than working from drawings, and we account for that in the scope when we quote the job.
You do not need a diagnosis before you call. You need a description, and we will take it from there.
Call (949) 514-6953 and describe what you are seeing.
We are available every day from 6 AM to 9 PM, and Tustin Electrical Company gives you a price before anything is booked.
You schedule it. We power it. Simple as that.
Electrical work also reaches these towns: Perris, Temescal Valley, Rancho Mission Viejo, Coto de Caza, Riverside.
Everywhere else we go is in our town-by-town list.
Electrical work covers a wide range of jobs, and knowing what each one involves helps you make a faster, more confident call. The table below breaks down the services we handle across Wildomar and Riverside County, what each one covers, and who it is most useful for. If a job is not on your radar yet, the FAQ section below covers the questions homeowners and property managers ask most often before they pick up the phone.
| Service Type | What's Included | Common Situations | Worth Knowing |
|---|---|---|---|
| Dedicated Appliance Circuits | 240V circuits for dryers and ranges, Refrigerator and dishwasher circuits, Workshop and compressor outlets, Pool pump and hot tub supply wiring | Homeowners adding a major appliance, finishing a garage, or setting up a workshop | A dedicated circuit isolates the appliance load so it runs on its own breaker with no competition from other devices, which reduces nuisance tripping and protects the appliance over time. |
| Electrical Panel and Service Upgrades | Panel replacement and load calculation, Fuse-box-to-breaker conversion, 200-amp service upgrades, Subpanel installation | Older homes, properties preparing for sale or renovation, and any home adding EV charging or solar | A 100-amp service is often the limiting factor in older Wildomar neighborhoods. Upgrading to 200 amps resolves capacity issues and brings the service entrance up to current standards. |
| EV Charger Installation | Panel capacity check, Dedicated 240V circuit run, Hardwired or outlet-based charger connection, Panel upgrade if needed | Riverside County homeowners adding a Level 2 home charger for overnight charging | Riverside County has one of the highest rates of EV ownership in the country. We confirm panel capacity first so the charger circuit does not push the service past what it can safely carry. |
Call (949) 514-6953 to go over the job on the phone and get a clear price before anything is scheduled.
(949) 514-6953